What're your opinions concerning A Step-by-Step Guide to Installing a Bathtub?

Setting up a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, and also often, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough task. If the old bathtub is conveniently available, the project can move immediately; if you need to open up a wall to eliminate the old tub and position the brand-new bathtub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly require a helper to leave the old tub as well as embeded in the new one. Ensure you have certified yourself for the work and also are comfortable trying it. As opposed to working with a contractor to take control of a halfway-completed job, it is better to consider using one prior to you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly aid you set up a new bathtub in your shower room if you have actually currently acquired a brand-new tub as well as do not require to transform the setup of your previous water system pipelines.
Your devices as well as product checklist need to make up the following:
- New Bathtub
- Hammer
- Pipe Wrenches
- Prybar
- Safety Glasses
- Level
- Pliers
- Adjustable Wrench
- Putty Knife
- Screwdriver
- Cold Blade
- Tape Measure
- Pipeline Caps
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, after that the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will come from the pipes. Once the supply pipes have been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to prevent damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Protect the tap in position with the maker offered backnut. Once the tap is firmly in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal tap adapters. The previous type ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing the two wood boards under its feet, place the tub in the required setting. The wooden boards are practical in evenly spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and changing the feet on the tub till the level reviews level.
To install faucets, fit all-time low of the furthest versatile faucet adapter to the ideal supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the water supply as well as examine all joints and new pipework for leaks and tighten them if necessary. Fill up the bath tub and also examine the overflow outlet as well as the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait till the bath tub has been made use of at the very least when as this will resolve it right into its final placement.
Getting ready for the Installment
First of all, the sustaining framework provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets device to stop strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last placement.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a stiff seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, causing complications with dampness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can split fairly early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is a good idea to fit the tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As a fervent person who reads on A Step-by-Step Guide to Installing a Bathtub, I thought sharing that portion was essential. I beg you take the opportunity to distribute this blog entry if you enjoyed reading it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .
Request expert assessment.
Comments on “Why Learning Plumbing Basics is Vital for Bathtub Installation”